Caps dump for model 2401
Model name:	EKD-500
Mfg name:	RFT
Backend version:	0.4
Backend copyright:	LGPL
Backend status:	Alpha
Rig type:	Receiver
PTT type:	None
DCD type:	None
Port type:	RS-232
Serial speed: 300..2400 bauds, 7E2 CTS/RTS
Write delay 0ms, timeout 200ms, 3 retry
Post Write delay 1ms
Has targetable VFO: no
Has transceive: no
Announce: 0x0
Max RIT: -0.0kHz/+0.0kHz
Max XIT: -0.0kHz/+0.0kHz
Max IF-SHIFT: -0.0kHz/+0.0kHz
Preamp: none
Attenuator: none
CTCSS: none
DCS: none
Get functions: 
Set functions: 
Get level: 
Set level: 
Extra levels:
Get parameters: 
Set parameters: 
Extra parameters:
VFO list: VFOA 
VFO Ops: 
Scan Ops: 
Number of banks:	0
Memory name desc size:	7
Memories: none
TX ranges status, region 1:	OK (0)
RX ranges status, region 1:	OK (0)
TX ranges status, region 2:	OK (0)
RX ranges status, region 2:	OK (0)
Tuning steps:
	10 Hz:   	AM CW USB LSB RTTY FM 
Tuning steps status:	OK (0)
Filters:
	2.2 kHz:   	AM CW USB LSB RTTY 
	12 kHz:   	FM 
Bandwidths:
	AM	normal: 2.2 kHz,	narrow: 0 Hz,	wide: 0 Hz
	CW	normal: 2.2 kHz,	narrow: 0 Hz,	wide: 0 Hz
	USB	normal: 2.2 kHz,	narrow: 0 Hz,	wide: 0 Hz
	LSB	normal: 2.2 kHz,	narrow: 0 Hz,	wide: 0 Hz
	RTTY	normal: 2.2 kHz,	narrow: 0 Hz,	wide: 0 Hz
	FM	normal: 12 kHz,	narrow: 0 Hz,	wide: 0 Hz
Has priv data:	N
Has init:	N
Has cleanup:	N
Has open:	N
Has close:	N
Can set conf:	N
Can get conf:	N
Can set frequency:	Y
Can get frequency:	N
Can set mode:	N
Can get mode:	N
Can set vfo:	N
Can get vfo:	N
Can set ptt:	N
Can get ptt:	N
Can get dcd:	N
Can set repeater duplex:	N
Can get repeater duplex:	N
Can set repeater offset:	N
Can get repeater offset:	N
Can set split freq:	N
Can get split freq:	N
Can set split mode:	N
Can get split mode:	N
Can set split vfo:	N
Can get split vfo:	N
Can set tuning step:	N
Can get tuning step:	N
Can set RIT:	N
Can get RIT:	N
Can set XIT:	N
Can get XIT:	N
Can set CTCSS:	N
Can get CTCSS:	N
Can set DCS:	N
Can get DCS:	N
Can set CTCSS squelch:	N
Can get CTCSS squelch:	N
Can set DCS squelch:	N
Can get DCS squelch:	N
Can set power stat:	N
Can get power stat:	N
Can reset:	N
Can get ant:	N
Can set ant:	N
Can set transceive:	N
Can get transceive:	N
Can set func:	N
Can get func:	N
Can set level:	N
Can get level:	N
Can set param:	N
Can get param:	N
Can send DTMF:	N
Can recv DTMF:	N
Can send Morse:	N
Can decode events:	N
Can set bank:	N
Can set mem:	N
Can get mem:	N
Can set channel:	N
Can get channel:	N
Can ctl mem/vfo:	N
Can scan:	N
Can get info:	N

Overall backend warnings: 0