Caps dump for model: 5016
Model name:	SR2200
Mfg name:	AOR
Backend version:	20200404.0
Backend copyright:	LGPL
Backend status:	Beta
Rig type:	Scanner
PTT type:	None
DCD type:	Rig capable
Port type:	RS-232
Serial speed: 19200..38400 bauds, 8N2 XONXOFF
Write delay: 0mS, timeout 200mS, 3 retry
Post Write delay: 0mS
Has targetable VFO: N
Has transceive: Y
Announce: 0x0
Max RIT: -0.0kHz/+0.0kHz
Max XIT: -0.0kHz/+0.0kHz
Max IF-SHIFT: -0.0kHz/+0.0kHz
Preamp: 10dB
Attenuator: 10dB 20dB
CTCSS: None
DCS: None
Get functions: 
Set functions: 
Extra functions:
Get level: PREAMP(0..0/0) ATT(0..0/0) AF(0..0/0) AGC(0..0/0) STRENGTH(0..0/0) 
Set level: PREAMP(0..0/0) ATT(0..0/0) AF(0..0/0) AGC(0..0/0) 
Extra levels:
Get parameters: 
Set parameters: 
Extra parameters:
Mode list: AM FM WFM 
VFO list: VFOA VFOB VFOC 
VFO Ops: MCL UP DOWN 
Scan Ops: MEM SLCT PROG VFO 
Number of banks:	10
Memory name desc size:	8
Memories:
	0..999:   	MEM
	  Mem caps: BANK FREQ MODE WIDTH TS FUNC LEVEL FLAG NAME 
TX ranges #1 for TBD:
RX ranges #1 for TBD:
	25000000 Hz - 3000000000 Hz
		VFO list: VFOA VFOB VFOC 
		Mode list: AM FM WFM 
		Antenna list: ANT_NONE
TX ranges #2 for TBD:
RX ranges #2 for TBD:
	25000000 Hz - 3000000000 Hz
		VFO list: VFOA VFOB VFOC 
		Mode list: AM FM WFM 
		Antenna list: ANT_NONE
TX ranges #3 for TBD:
RX ranges #3 for TBD:
TX ranges #4 for TBD:
RX ranges #4 for TBD:
TX ranges #5 for TBD:
RX ranges #5 for TBD:
TX ranges #1 status for TBD:	OK (0)
RX ranges #1 status for TBD:	OK (0)
TX ranges #2 status for TBD:	OK (0)
RX ranges #2 status for TBD:	OK (0)
TX ranges #3 status for TBD:	OK (0)
RX ranges #3 status for TBD:	OK (0)
TX ranges #4 status for TBD:	OK (0)
RX ranges #4 status for TBD:	OK (0)
TX ranges #5 status for TBD:	OK (0)
RX ranges #5 status for TBD:	OK (0)
Tuning steps:
	1 Hz:   	AM FM WFM 
	100 Hz:   	AM FM WFM 
	500 Hz:   	AM FM WFM 
	1 kHz:   	AM FM WFM 
	2 kHz:   	AM FM WFM 
	5 kHz:   	AM FM WFM 
	6.25 kHz:   	AM FM WFM 
	9 kHz:   	AM FM WFM 
	10 kHz:   	AM FM WFM 
	12.5 kHz:   	AM FM WFM 
	20 kHz:   	AM FM WFM 
	25 kHz:   	AM FM WFM 
	30 kHz:   	AM FM WFM 
	50 kHz:   	AM FM WFM 
	100 kHz:   	AM FM WFM 
Tuning steps status:	OK (0)
Filters:
	6 kHz:   	AM 
	15 kHz:   	AM 
	15 kHz:   	FM 
	6 kHz:   	FM 
	300 kHz:   	WFM 
Bandwidths:
	AM	Normal: 6 kHz,	Narrow: 0 Hz,	Wide: 15 kHz
	FM	Normal: 15 kHz,	Narrow: 6 kHz,	Wide: 0 Hz
	WFM	Normal: 300 kHz,	Narrow: 0 Hz,	Wide: 0 Hz
Has priv data:	Y
Has Init:	N
Has Cleanup:	N
Has Open:	N
Has Close:	N
Can set Conf:	N
Can get Conf:	N
Can set Frequency:	Y
Can get Frequency:	Y
Can set Mode:	Y
Can get Mode:	Y
Can set VFO:	Y
Can get VFO:	Y
Can set PTT:	N
Can get PTT:	N
Can get DCD:	Y
Can set Repeater Duplex:	N
Can get Repeater Duplex:	N
Can set Repeater Offset:	N
Can get Repeater Offset:	N
Can set Split Freq:	N
Can get Split Freq:	N
Can set Split Mode:	N
Can get Split Mode:	N
Can set Split VFO:	N
Can get Split VFO:	N
Can set Tuning Step:	Y
Can get Tuning Step:	N
Can set RIT:	N
Can get RIT:	N
Can set XIT:	N
Can get XIT:	N
Can set CTCSS:	N
Can get CTCSS:	N
Can set DCS:	N
Can get DCS:	N
Can set CTCSS Squelch:	N
Can get CTCSS Squelch:	N
Can set DCS Squelch:	N
Can get DCS Squelch:	N
Can set Power Stat:	Y
Can get Power Stat:	N
Can Reset:	N
Can get Ant:	N
Can set Ant:	N
Can set Transceive:	E
Can get Transceive:	N
Can set Func:	N
Can get Func:	N
Can set Level:	Y
Can get Level:	Y
Can set Param:	N
Can get Param:	N
Can send DTMF:	N
Can recv DTMF:	N
Can send Morse:	N
Can send Voice:	N
Can decode Events:	N
Can set Bank:	Y
Can set Mem:	Y
Can get Mem:	Y
Can set Channel:	Y
Can get Channel:	Y
Can ctl Mem/VFO:	Y
Can Scan:	Y
Can get Info:	Y
Can get power2mW:	N
Can get mW2power:	N

Overall backend warnings: 0