Caps dump for model: 3086
Model name:	IC-F8101
Mfg name:	Icom
Hamlib version:	Hamlib 4.6.5 from indeterminate source revision. 64-bit
Backend version:	20250517.3
Backend copyright:	LGPL
Backend status:	Stable
Rig type:	Other Receiver Transmitter Transceiver 
PTT type:	None
DCD type:	Rig capable
Port type:	RS-232
Serial speed: 300..19200 baud, 8N1, ctrl=NONE
Write delay: 0ms, timeout 1000ms, 3 retry
Post write delay: 0ms
Has targetable VFO: Y
Targetable features: FREQ
Has async data support: N
Announce: 0x0
Max RIT: -0.0kHz/+0.0kHz
Max XIT: -0.0kHz/+0.0kHz
Max IF-SHIFT: -0.0kHz/+0.0kHz
Preamp: 20dB
Attenuator: 20dB
AGC levels: 9=NONE
CTCSS: None
DCS: None
Get functions: NB COMP VOX TONE FBKIN ANF NR AFC 
Set functions: NB COMP VOX TONE FBKIN ANF NR AFC RESUME 
Extra functions:
Get level: PREAMP(0..0/0) ATT(0..0/0) AF(0.000000..0.000000/0.000000) RF(0.000000..0.000000/0.000000) SQL(0.000000..0.000000/0.000000) IF(0..0/0) NR(0.000000..0.000000/0.000000) RFPOWER(0.000000..0.000000/0.000000) MICGAIN(0.000000..0.000000/0.000000) RAWSTR(0..255/0) 
Set level: PREAMP(0..0/0) ATT(0..0/0) AF(0.000000..0.000000/0.000000) RF(0.000000..0.000000/0.000000) SQL(0.000000..0.000000/0.000000) IF(0..0/0) NR(0.000000..0.000000/0.000000) RFPOWER(0.000000..0.000000/0.000000) MICGAIN(0.000000..0.000000/0.000000) 
Extra levels:
Get parameters: 
Set parameters: 
Extra parameters:
Mode list: AM CW USB LSB RTTY
VFO list: VFOA VFOB 
VFO Ops: 
Scan Ops: MEM 
Number of banks:	0
Memory name desc size:	0
Memories:
	1..500:   	MEM
	  Mem caps: 
TX ranges #1 for Other:
	1600000 Hz - 29999900 Hz
		VFO list: VFOA VFOB 
		Mode list: AM CW USB LSB RTTY
		Antenna list: ANT_CURR 
		Low power: 1 W, High power: 100 W
RX ranges #1 for Other:
	500000 Hz - 29999900 Hz
		VFO list: VFOA VFOB 
		Mode list: AM CW USB LSB RTTY
		Antenna list: ANT_CURR 
TX ranges #2 for AUS:
RX ranges #2 for AUS:
	500000 Hz - 29999900 Hz
		VFO list: VFOA VFOB 
		Mode list: AM CW USB LSB RTTY
		Antenna list: ANT_CURR 
TX ranges #3 for TBD:
RX ranges #3 for TBD:
TX ranges #4 for TBD:
RX ranges #4 for TBD:
TX ranges #5 for TBD:
RX ranges #5 for TBD:
TX ranges #1 status for Other:	OK (0)
RX ranges #1 status for Other:	OK (0)
TX ranges #2 status for AUS:	OK (0)
RX ranges #2 status for AUS:	OK (0)
TX ranges #3 status for TBD:	OK (0)
RX ranges #3 status for TBD:	OK (0)
TX ranges #4 status for TBD:	OK (0)
RX ranges #4 status for TBD:	OK (0)
TX ranges #5 status for TBD:	OK (0)
RX ranges #5 status for TBD:	OK (0)
Tuning steps:
	1.0 Hz:   	AM CW USB LSB RTTY
Tuning steps status:	OK (0)
Filters:
	3.0000 kHz:   	 CW USB LSB RTTY
	10.0000 kHz:   	AM
Bandwidths:
	AM	Normal: 10.0000 kHz,	Narrow: 0.0 Hz,	Wide: 0.0 Hz
	CW	Normal: 3.0000 kHz,	Narrow: 0.0 Hz,	Wide: 0.0 Hz
	USB	Normal: 3.0000 kHz,	Narrow: 0.0 Hz,	Wide: 0.0 Hz
	LSB	Normal: 3.0000 kHz,	Narrow: 0.0 Hz,	Wide: 0.0 Hz
	RTTY	Normal: 3.0000 kHz,	Narrow: 0.0 Hz,	Wide: 0.0 Hz
	CWR	Normal: 3.0000 kHz,	Narrow: 0.0 Hz,	Wide: 0.0 Hz
	RTTYR	Normal: 3.0000 kHz,	Narrow: 0.0 Hz,	Wide: 0.0 Hz
Spectrum scopes: None
Spectrum modes: 
Spectrum spans: 
Spectrum averaging modes: 
Spectrum attenuator: None
Has priv data:	Y
Has Init:	Y
Has Cleanup:	Y
Has Open:	Y
Has Close:	Y
Can set Conf:	Y
Can get Conf:	Y
Can set Frequency:	Y
Can get Frequency:	Y
Can set Mode:	Y
Can get Mode:	Y
Can set VFO:	Y
Can get VFO:	N
Can set PTT:	Y
Can get PTT:	Y
Can get DCD:	Y
Can set Repeater Duplex:	N
Can get Repeater Duplex:	N
Can set Repeater Offset:	N
Can get Repeater Offset:	N
Can set Split Freq:	Y
Can get Split Freq:	Y
Can set Split Mode:	E
Can get Split Mode:	E
Can set Split VFO:	Y
Can get Split VFO:	Y
Can set Tuning Step:	Y
Can get Tuning Step:	Y
Can set RIT:	N
Can get RIT:	N
Can set XIT:	N
Can get XIT:	N
Can set CTCSS:	N
Can get CTCSS:	N
Can set DCS:	N
Can get DCS:	N
Can set CTCSS Squelch:	N
Can get CTCSS Squelch:	N
Can set DCS Squelch:	N
Can get DCS Squelch:	N
Can set Power Stat:	N
Can get Power Stat:	N
Can Reset:	N
Can get Ant:	N
Can set Ant:	N
Can set Transceive:	E
Can get Transceive:	N
Can set Func:	Y
Can get Func:	Y
Can set Level:	Y
Can get Level:	Y
Can set Param:	N
Can get Param:	N
Can send DTMF:	N
Can recv DTMF:	N
Can send Morse:	N
Can stop Morse:	N
Can wait Morse:	N
Can send Voice:	N
Can decode Events:	Y
Can set Bank:	N
Can set Mem:	Y
Can get Mem:	N
Can set Channel:	N
Can get Channel:	N
Can ctl Mem/VFO:	Y
Can Scan:	Y
Can get Info:	N
Can get power2mW:	N
Can get mW2power:	N

Overall backend warnings: 0