Caps dump for model: 2015
Model name:	R-5000
Mfg name:	Kenwood
Hamlib version:	Hamlib 4.7.0 from indeterminate source revision. 64-bit
Backend version:	20231002.1
Backend copyright:	LGPL
Backend status:	Stable
Rig type:	Other Receiver 
PTT type:	None
DCD type:	None
Port type:	RS-232
Serial speed: 4800..4800 baud, 8N2, ctrl=NONE
Write delay: 0ms, timeout 500ms, 3 retry
Post write delay: 2ms
Has targetable VFO: Y
Targetable features: FREQ
Has async data support: N
Announce: 0x0
Max RIT: -0.0kHz/+0.0kHz
Max XIT: -0.0kHz/+0.0kHz
Max IF-SHIFT: -0.0kHz/+0.0kHz
Preamp: None
Attenuator: None
AGC levels: 9=NONE
CTCSS: None
DCS: None
Get functions: LOCK 
Set functions: LOCK 
Extra functions:
Get level: 
Set level: 
Extra levels:
Get parameters: TIME(0..86399/1) 
Set parameters: TIME(0..86399/1) 
Extra parameters:
Mode list: AM CW USB LSB RTTY FM
VFO list: VFOA VFOB MEM 
VFO Ops: UP DOWN 
Scan Ops: VFO 
Number of banks:	0
Memory name desc size:	0
Memories:
	0..99:   	MEM
	  Mem caps: FREQ MODE TXFREQ TXMODE 
TX ranges #1 for TBD:
RX ranges #1 for TBD:
	100000 Hz - 30000000 Hz
		VFO list: VFOA VFOB MEM 
		Mode list: AM CW USB LSB RTTY FM
		Antenna list: ANT_NONE
	108000000 Hz - 174000000 Hz
		VFO list: VFOA VFOB MEM 
		Mode list: AM CW USB LSB RTTY FM
		Antenna list: ANT_NONE
TX ranges #2 for TBD:
RX ranges #2 for TBD:
	100000 Hz - 30000000 Hz
		VFO list: VFOA VFOB MEM 
		Mode list: AM CW USB LSB RTTY FM
		Antenna list: ANT_NONE
	108000000 Hz - 174000000 Hz
		VFO list: VFOA VFOB MEM 
		Mode list: AM CW USB LSB RTTY FM
		Antenna list: ANT_NONE
TX ranges #3 for TBD:
RX ranges #3 for TBD:
TX ranges #4 for TBD:
RX ranges #4 for TBD:
TX ranges #5 for TBD:
RX ranges #5 for TBD:
TX ranges #1 status for TBD:	OK (0)
RX ranges #1 status for TBD:	OK (0)
TX ranges #2 status for TBD:	OK (0)
RX ranges #2 status for TBD:	OK (0)
TX ranges #3 status for TBD:	OK (0)
RX ranges #3 status for TBD:	OK (0)
TX ranges #4 status for TBD:	OK (0)
RX ranges #4 status for TBD:	OK (0)
TX ranges #5 status for TBD:	OK (0)
RX ranges #5 status for TBD:	OK (0)
Tuning steps:
	10.0 Hz:   	AM CW USB LSB RTTY FM
Tuning steps status:	OK (0)
Filters:
	2.4000 kHz:   	 CW USB LSB RTTY
	6.0000 kHz:   	AM
	12.0000 kHz:   	 FM
Bandwidths:
	AM	Normal: 6.0000 kHz,	Narrow: 0.0 Hz,	Wide: 0.0 Hz
	CW	Normal: 2.4000 kHz,	Narrow: 0.0 Hz,	Wide: 0.0 Hz
	USB	Normal: 2.4000 kHz,	Narrow: 0.0 Hz,	Wide: 0.0 Hz
	LSB	Normal: 2.4000 kHz,	Narrow: 0.0 Hz,	Wide: 0.0 Hz
	RTTY	Normal: 2.4000 kHz,	Narrow: 0.0 Hz,	Wide: 0.0 Hz
	FM	Normal: 12.0000 kHz,	Narrow: 0.0 Hz,	Wide: 0.0 Hz
	CWR	Normal: 2.4000 kHz,	Narrow: 0.0 Hz,	Wide: 0.0 Hz
	RTTYR	Normal: 2.4000 kHz,	Narrow: 0.0 Hz,	Wide: 0.0 Hz
Spectrum scopes: None
Spectrum modes: 
Spectrum spans: 
Spectrum averaging modes: 
Spectrum attenuator: None
Has priv data:	Y
Has Init:	Y
Has Cleanup:	Y
Has Open:	Y
Has Close:	Y
Can set Conf:	N
Can get Conf:	N
Can set Frequency:	Y
Can get Frequency:	Y
Can set Mode:	Y
Can get Mode:	Y
Can set VFO:	Y
Can get VFO:	Y
Can set PTT:	N
Can get PTT:	N
Can get DCD:	N
Can set Repeater Duplex:	N
Can get Repeater Duplex:	N
Can set Repeater Offset:	N
Can get Repeater Offset:	N
Can set Split Freq:	N
Can get Split Freq:	N
Can set Split Mode:	N
Can get Split Mode:	N
Can set Split VFO:	N
Can get Split VFO:	N
Can set Tuning Step:	N
Can get Tuning Step:	N
Can set RIT:	N
Can get RIT:	N
Can set XIT:	N
Can get XIT:	N
Can set CTCSS:	N
Can get CTCSS:	N
Can set DCS:	N
Can get DCS:	N
Can set CTCSS Squelch:	N
Can get CTCSS Squelch:	N
Can set DCS Squelch:	N
Can get DCS Squelch:	N
Can set Power Stat:	Y
Can get Power Stat:	Y
Can Reset:	N
Can get Ant:	Y
Can set Ant:	Y
Can set Transceive:	Y
Can get Transceive:	Y
Can set Func:	Y
Can get Func:	Y
Can set Level:	N
Can get Level:	N
Can set Param:	Y
Can get Param:	Y
Can send DTMF:	N
Can recv DTMF:	N
Can send Morse:	N
Can stop Morse:	N
Can wait Morse:	N
Can send Voice:	N
Can decode Events:	Y
Can set Bank:	N
Can set Mem:	Y
Can get Mem:	Y
Can set Channel:	Y
Can get Channel:	Y
Can ctl Mem/VFO:	Y
Can Scan:	Y
Can get Info:	Y
Can get power2mW:	N
Can get mW2power:	N

Overall backend warnings: 0