Caps dump for model: 2038
Model name:	XG3
Mfg name:	Elecraft
Hamlib version:	Hamlib 4.7.0 from indeterminate source revision. 64-bit
Backend version:	20230305.0
Backend copyright:	LGPL
Backend status:	Stable
Rig type:	Other Receiver Transmitter Transceiver 
PTT type:	None
DCD type:	Rig capable
Port type:	RS-232
Serial speed: 9600..9600 baud, 8N1, ctrl=NONE
Write delay: 0ms, timeout 25ms, 3 retry
Post write delay: 25ms
Has targetable VFO: Y
Targetable features: FREQ
Has async data support: N
Announce: 0x0
Max RIT: -0.0kHz/+0.0kHz
Max XIT: -0.0kHz/+0.0kHz
Max IF-SHIFT: -0.0kHz/+0.0kHz
Preamp: None
Attenuator: None
AGC levels: 9=NONE
CTCSS: None
DCS: None
Get functions: 
Set functions: 
Extra functions:
Get level: RFPOWER(0.050000..1.000000/0.010000) 
Set level: RFPOWER(0.050000..1.000000/0.010000) 
Extra levels:
Get parameters: BACKLIGHT(0..0/0) 
Set parameters: BACKLIGHT(0..0/0) 
Extra parameters:
	fine
		Type: CHECKBUTTON
		Default: 
		Label: Fine
		Tooltip: Fine step mode
	voice
		Type: BUTTON
		Default: 
		Label: Voice
		Tooltip: Voice recall
	xit
		Type: CHECKBUTTON
		Default: 
		Label: XIT
		Tooltip: XIT
	rit
		Type: CHECKBUTTON
		Default: 
		Label: RIT
		Tooltip: RIT
	no_id
		Type: CHECKBUTTON
		Default: 
		Label: No ID
		Tooltip: If true do not send ID; with set commands
Mode list:  CW
VFO list: VFOA 
VFO Ops: 
Scan Ops: 
Number of banks:	0
Memory name desc size:	0
Memories:
	0..11:   	MEM
	  Mem caps: FREQ 
TX ranges #1 for TBD:
	1500000 Hz - 200000000 Hz
		VFO list: VFOA 
		Mode list:  CW
		Antenna list: ANT1 
		Low power: 0 W, High power: 0.002 W
RX ranges #1 for TBD:
TX ranges #2 for TBD:
RX ranges #2 for TBD:
TX ranges #3 for TBD:
RX ranges #3 for TBD:
TX ranges #4 for TBD:
RX ranges #4 for TBD:
TX ranges #5 for TBD:
RX ranges #5 for TBD:
TX ranges #1 status for TBD:	OK (0)
RX ranges #1 status for TBD:	OK (0)
TX ranges #2 status for TBD:	OK (0)
RX ranges #2 status for TBD:	OK (0)
TX ranges #3 status for TBD:	OK (0)
RX ranges #3 status for TBD:	OK (0)
TX ranges #4 status for TBD:	OK (0)
RX ranges #4 status for TBD:	OK (0)
TX ranges #5 status for TBD:	OK (0)
RX ranges #5 status for TBD:	OK (0)
Tuning steps:
	ANY:   	AM CW USB LSB RTTY FM WFM CWR RTTYR AMS PKTLSB PKTUSB FM-D ECSSUSB ECSSLSB FAX SAM SAL SAH DSB FMN AM-D P25 D-STAR DPMR NXDN-VN NXDN-N DCR AMN PSK PSKR
Tuning steps status:	OK (0)
Filters:
	ANY:   	AM CW USB LSB RTTY FM WFM CWR RTTYR AMS PKTLSB PKTUSB FM-D ECSSUSB ECSSLSB FAX SAM SAL SAH DSB FMN AM-D P25 D-STAR DPMR NXDN-VN NXDN-N DCR AMN PSK PSKR
Bandwidths:
Spectrum scopes: None
Spectrum modes: 
Spectrum spans: 
Spectrum averaging modes: 
Spectrum attenuator: None
Has priv data:	Y
Has Init:	Y
Has Cleanup:	Y
Has Open:	Y
Has Close:	N
Can set Conf:	N
Can get Conf:	N
Can set Frequency:	Y
Can get Frequency:	Y
Can set Mode:	N
Can get Mode:	N
Can set VFO:	Y
Can get VFO:	Y
Can set PTT:	Y
Can get PTT:	Y
Can get DCD:	N
Can set Repeater Duplex:	N
Can get Repeater Duplex:	N
Can set Repeater Offset:	N
Can get Repeater Offset:	N
Can set Split Freq:	N
Can get Split Freq:	N
Can set Split Mode:	N
Can get Split Mode:	N
Can set Split VFO:	N
Can get Split VFO:	N
Can set Tuning Step:	N
Can get Tuning Step:	N
Can set RIT:	N
Can get RIT:	N
Can set XIT:	N
Can get XIT:	N
Can set CTCSS:	N
Can get CTCSS:	N
Can set DCS:	N
Can get DCS:	N
Can set CTCSS Squelch:	N
Can get CTCSS Squelch:	N
Can set DCS Squelch:	N
Can get DCS Squelch:	N
Can set Power Stat:	Y
Can get Power Stat:	Y
Can Reset:	N
Can get Ant:	N
Can set Ant:	N
Can set Transceive:	E
Can get Transceive:	N
Can set Func:	N
Can get Func:	N
Can set Level:	Y
Can get Level:	Y
Can set Param:	Y
Can get Param:	Y
Can send DTMF:	N
Can recv DTMF:	N
Can send Morse:	N
Can stop Morse:	N
Can wait Morse:	N
Can send Voice:	N
Can decode Events:	N
Can set Bank:	N
Can set Mem:	Y
Can get Mem:	Y
Can set Channel:	N
Can get Channel:	N
Can ctl Mem/VFO:	N
Can Scan:	N
Can get Info:	N
Can get power2mW:	N
Can get mW2power:	N

Overall backend warnings: 0